더블 다이

동전 에러 중 “이중 도장 (Doubled die)”으로 알려진 것은 다이 제작 단계에서의 정렬 오류로 인해 발생합니다. 특히 허브에서 이미지를 돈을 찍을 다이로 이전하는 과정에서 발생합니다. 다이는 수백 톤의 압력으로 허브를 처음 사용하는 다이에 압축하여 만들어집니다. 다이에 사용된 강철의 단단함으로 인해 이후의 압축으로는 이전의 압축을 완전히 지울 수 없습니다. 따라서 허브와 다이가 연속적인 압축에서 정렬되지 않으면 다이에 나타나는 이미지는 이전 압축의 흔적을 나타내며, 이것을 “이중 효과”라고 합니다.
이중 효과는 두 가지 방법으로 발생할 수 있으며, 다이의 전체 면 또는 보통 다이 중앙에 발생하는 특정 영역에 영향을 줍니다. 정렬 오류의 종류에 따라 이중 도장 에러의 8가지 식별 가능한 클래스가 있습니다.
클래스 I는 회전 이중 (Rotated doubling)으로, 허브가 연속적인 압축에서 축을 중심으로 회전하면서 다이와 다이에서 찍힌 동전에 두 개의 분할 이미지가 생성됩니다. 가장 강한 인상은 두 번째 압축에서 만들어지며, 회전 지점은 보통 중앙에 있습니다.
클래스 II는 변형 이중 (Distorted doubling)으로, 압축 중 하나에서 변형된 펀치를 사용할 때 발생합니다. 이 변형은 펀치의 장기간 사용으로 인해 발생할 수 있으며, 다이의 중앙 또는 가장자리로 약간 변형되고 늘어난 이미지가 생성됩니다.
클래스 III는 서로 다른 인상을 가진 이중 (Doubling with different imprint)으로, 하나 이상의 요소가 약간 다르거나 다른 위치에 있는 허브가 압축 중 하나에서 사용될 때 발생합니다.
클래스 IV는 이동 이중 (Displaced doubling)으로, 연속 압축 중 허브가 축을 중심으로 어느 방향으로든 이동할 때 발생합니다.
클래스 V는 핀을 가진 이중 (Doubling with pin)으로, 허브가 다이 표면의 점을 중심으로 회전하거나 이동할 때 발생합니다. 이중 효과는 핀과 반대편 지점에서 최대 폭을 갖게 되면서 “부채꼴” 모양으로 열리게 됩니다.
In addition to the five major classes of doubled die errors, there are also three minor classes. These minor classes are characterized by variations in the doubling effect that are less pronounced or less common.
Class VI – Distended doubling: This class occurs when the hub is compressed too strongly against the die, causing the metal to be pushed outward and creating a slightly distended image. This type of doubling is usually less pronounced and less common than the other classes.
Class VII – Pivoted doubling: This class occurs when the hub is rotated or moved on a point that is not located on the face of the die. In this case, the doubling effect will be more pronounced in the area opposite the pivot point.
Class VIII – Design rim doubling: This class occurs when the doubling effect is limited to the rim of the coin and does not affect the design elements. This type of doubling is generally less noticeable and less valuable than the other classes of doubled die errors.